Quick Details

• Place of Origin:

  China

• Samples:

  Free

• Delivery Time:

  20days After Siging Contract

• Packing:

  Perfect Boxes

• Delivery Port:

  Shanghai

• Max. Production Capacity:

  1000000

• Export Ratio:

  51% - 60%

• OE Experience:

  No

Product Name:Free Sample Hitachi Carbon Brush 04623110

Free Sample Hitachi Carbon Brush 04623110

Application

Hitachi Bosch

Product Description:

OEM No/Model: 04623110
Free Sample -AUTO CARBON BRUSH we can supply various kinds of carbon brush for AUTO ,our brushes have characters ,used such as long time,low spark. 1, from the appearance point of view: This product chamfer decent, appropriate specifications, structure specifications the wire cross-section and length, not loose, falling off, broken off side, off angle, clamp and so on. 2, from the use of terms: (1) The product of high quality graphite, long life and do not wear commutator or slip rings, commutator appears not to scratch, rough, ablation, drawing and so on. (2) has a good flow properties and set to change, so that spark suppression in the permitted range, and the energy loss is small. (3) brush runs, but heat, noise, not broken, do not change color brush braid, no ablation. (4) is running, can the surface of commutator or collector ring quickly form a uniform, moderate and stable oxide film. Information for your reference Carbon brush performance Commutator: Unit must be in good condition, with less than .002" out-of-roundness. Bar edge must be chamfered and there should be no burned edges. Brush Holders : They must be mechanically sound and permit the brush to slide freely. Brush holder fingers must move freely and if the unit consists of constant pressure springs, these springs must be in good condition. Springs that are difficult to move, have an excessive accumulation of carbon, or are worn, will cause excessive brush wear. Brush Holder Angles: The angles should be set to the original manufacturer s specification. Any more than a 2 degree variation in the setting can cause arcing, bar burning, and excessive wear. Brush holders that vary in the angle set to the commutator will cause the unit to be "off neutral". Brush Holder Spring Tension: Maintaining the proper spring pressure reduces arcing, brush wear, heating, and commutator wear. Light spring tension can cause threading and definitely will shorten the brush life. As a general rule, we recommend that the brushes be set at 4 psi pressure. To calculate the pressure, measure the width and thickness of the contact face and calculate as follows: Pressure in Pounds/Brush = (Width x Thickness x 4 psi) Brush Holder Quartering: To insure that the best machine electrical neutral can be achieved, the brush holders must be quartered. Quartering is setting the brush holders at equal distance around the commutator. For a 4 pole machine, the spacing will be every 90 degrees. If the quartering is not properly set, you may experience excessive arcing, heating, brush wear, and commutator wear. Machine Neutral: To obtain optimum machine performance, the brush must be set at the machine electrical neutral. If the unit is off neutral, you may observe sparking under a no-load condition. Depending upon how far off neutral the machine is set, there may be arcing and bar burning.

Established in 2010, Haimen Bosheng Carbon Industry Co., Ltd. is specializing in producing various kinds of carbon products. Located in the middle part of Jiangsu Province, on the coast of East Sea, beside the Yangtze River, we enjoy convenient transportation. Our company mainly manufactures ...[Read More]

Company Profile:

• Main Product:

  Carbon Brushes, Power Tools, Motors and Micro Motors

• Business Type:

  Manufacturer

• Current Export Market:

  North America, South America, Western Europe, Eastern Europe, Eastern Asia, Southeast Asia, Mid East, Africa, Oceania

• Total Annual Sales:

  USD 500,001 - 1,000,000

Factory Profile:

• Number of Employees:

  Less than 50 People

• Shift:

  2

• Size of Factory In Square Meters:

  2000

• Years of OEM Experiences:

  1

• Equipment Name:

  Carbon Brush Machines

Research & Development:

• Capability for Synchronized Development:

  Develop according to drawing or samples provided by clients?Yes

  Develop 3-D model and prototype according to client's needs?Yes

• Lead Time for New Product Development:

  1MONTH

• Tooling Design:

  Design Internally, Outsourcing or Cooperation

• Source of Tooling:

  Made Internally

• Software/Profile:

  Unigraphics, AUTOCAD, Autodesk Inventor, Others