Quick Details

• Place of Origin:

  Hmbsh

• Samples:

  Free

• Delivery Time:

  Within 30days

• Delivery Port:

  Shanghai

• Max. Production Capacity:

  1,000,000 Per Month

• Export Ratio:

  51% - 60%

• OE Experience:

  No

Product Name:Free Samples-Automobile Starter Carbon Brush 3676325

Free Samples-Automobile Starter Carbon Brush 3676325

Application

Product Description:

OEM No/Model: 3676325

Carbon brush for Power Tools

         Automobile Starter Carbon Brush
 

      we can supply various kinds of Automobile Starter Carbon Brush,our carbon  brushes have characters ,used such as  long time,low spark.,

      we also can supply carbon brushes replacements, such as Hitachi series,Makita series,Bosch series,Dewalt series,Matao series,Black&Decker series.

 Information for your reference

                                                Carbon brush performance

Commutator:
Unit must be in good condition, with less than .002" out-of-roundness. Bar edge must be chamfered and there should be no burned edges.

Brush Holders:
They must be mechanically sound and permit the brush to slide freely. Brush holder fingers must move freely and if the unit consists of constant pressure springs, these springs must be in good condition. Springs that are difficult to move, have an excessive accumulation of carbon, or are worn, will cause excessive brush wear.

Brush Holder Angles:
The angles should be set to the original manufacturer's specification. Any more than a 2 degree variation in the setting can cause arcing, bar burning, and excessive wear. Brush holders that vary in the angle set to the commutator will cause the unit to be "off neutral".

Brush Holder Spring Tension:
Maintaining the proper spring pressure reduces arcing, brush wear, heating, and commutator wear. Light spring tension can cause threading and definitely will shorten the brush life. As a general rule, we recommend that the brushes be set at 4 psi pressure. To calculate the pressure, measure the width and thickness of the contact face and calculate as follows:

Pressure in Pounds/Brush = (Width x Thickness x 4 psi)

Brush Holder Quartering:
To insure that the best machine electrical neutral can be achieved, the brush holders must be quartered. Quartering is setting the brush holders at equal distance around the commutator. For a 4 pole machine, the spacing will be every 90 degrees. If the quartering is not properly set, you may experience excessive arcing, heating, brush wear, and commutator wear.

Machine Neutral:
To obtain optimum machine performance, the brush must be set at the machine electrical neutral. If the unit is off neutral, you may observe sparking under a no-load condition. Depending upon how far off neutral the machine is set, there may be arcing and bar burning.

Carbon Brushes Description

The Principal Dimensions of a Carbon Brush

Note: 
 
We work to NEMA and ANSI tolerances on the dimensions given to us. Width and thickness dimensions should be established accurately. If in doubt, it should be noted that the internal dimensions of the brush holder should be about .003" greater than the nominal dimensions of the brush.

Flexible length is the length from the top of the longest side of the brush to the center of the terminal hole.

The dimensions of "d" on the double shank terminals may vary with the flexible size, reducing as the flexible size increases and the minimum permissible dimension should be stated.

Terminals:
Please give the size of opening.

Established in 2010, Haimen Bosheng Carbon Industry Co., Ltd. is specializing in producing various kinds of carbon products. Located in the middle part of Jiangsu Province, on the coast of East Sea, beside the Yangtze River, we enjoy convenient transportation. Our company mainly manufactures ...[Read More]

Company Profile:

• Main Product:

  Carbon Brushes, Power Tools, Motors and Micro Motors

• Business Type:

  Manufacturer

• Current Export Market:

  North America, South America, Western Europe, Eastern Europe, Eastern Asia, Southeast Asia, Mid East, Africa, Oceania

• Total Annual Sales:

  USD 500,001 - 1,000,000

Factory Profile:

• Number of Employees:

  Less than 50 People

• Shift:

  2

• Size of Factory In Square Meters:

  2000

• Years of OEM Experiences:

  1

• Equipment Name:

  Carbon Brush Machines

Research & Development:

• Capability for Synchronized Development:

  Develop according to drawing or samples provided by clients?Yes

  Develop 3-D model and prototype according to client's needs?Yes

• Lead Time for New Product Development:

  1MONTH

• Tooling Design:

  Design Internally, Outsourcing or Cooperation

• Source of Tooling:

  Made Internally

• Software/Profile:

  Unigraphics, AUTOCAD, Autodesk Inventor, Others