Product Attribute:
Life:3000h
Color Temperature:3,000k
Voltage:9v
Applicationt: 
auto
Production Description:
HID conversion kit (H1.H3.H4.H7.H8.H9.H11.9005.9006.etc)
Color:3k to 30k or aboved
HID conversion kit detail as follow:
Main Technical Parameter:
HID lamp technical parameter:
Power
35W
Input Voltage
9V-16V
Standard Input Current
3.2A
Normal Operating Voltage
80V
Luminous flux
>3000lm
Color temperature
3000K,4300K,5000K,6000K,8000K,10000K,12000K
Lifetime
3000h
Ballast technical parameter:
Standard Input Voltage: 13.2V
Output power: 35W norm.
Voltage Accommodation Range: 9~16V
Electric Efficency: >85%
Standard Input Current: 3.2A
Maximum Input Current: 8A
Lifetime: >3000hrs
Momentary Maximum Ignition Voltage: 23KV
Ambient Temperature Range: -40~+105
Features of Xenon HID convertion kit:
Xenon-HID Conversion Kit is a true Plug-and-Play Kit, easy to convert. Our conversion kits fit into your headlight housing perfectly. No modification or retrofitting is required. No need to cut your stock headlight wiring.
1) Fits all vehicles with projector or reflector headlights.
2) Easy to install: Just connect the wiring harness from the stock headlight wiring to the ballast. From the ballast, connect the wiring harness from the ballast to the HID Bulbs. Put the HID Bulb back into your headlight housing and it is completed. Detailed instructions are included in the kit.
3) Longer lifetime (3000 hours) then traditional halogen bulbs, over 10 times longer on average.
4) Greater luminosity (3200lm) and low power consumption.
5) High safety:
Waterproof, dustproof and vibration resistant ballasts.
open circuit protection, short circuit protection, over voltage and less voltage protection ,bulb abnormity protection and anti-jamming. It can apply to very adverse conditions.
6) Bulb size:
H1.H3.H4-1.H4-2.H4-3.H4-4. H7.H8.H9.H10.H11.H13-1.H13-2.H13-3.H13-4.
9004-1/9004-2/9004-3/9004-4/9005/9006/9007-1/9007-2/9007-3/9007-4/D2C(D2R/S)/880/881.
7) Color temperature:
3,000K/4,300K/5,000K/6,000K/8,000K/10,000K/12,000K.or above.
We also carry extreme colors, Deep Blue/Purple/Green/Pink/Yellow.
Note: Our fraction defective is lower than 2%. If you purchase 100 sets at a time, 2 sets will be presented free.
Product and Accessories List:
· Two Xenon HID Bulbs ( Buyer chooses Bulb type and Color Temperature)
· Two Ballasts
· Two supports of Ballast
· Eight fixation buckles of wire
· Two screws
· One Operation Instruction
THE PROCESS FOR INSTALLATION:
1. Separate the headlamps (right&left)from your car after opening your car bonnet,if there is enough space for car bonnet,if there is enoughj space for exchange ,it is not needed to separate the headlamps from your car.
2. Open the rear cover of the headlamp and pull the installed halogen lamp out.
3. Drill a hole in the middle if the rear cover of the headlamp with a 21mm hole cutter.
4. Take out the plastic cap of the HID bulb.
5. Put the HID lamp into the headlamp unit.
6. Connecting the wires-referring to the wiring diagram in the guide book.
7. Close the cap of the headlamp after fitting the rubber barking attached to the bulbs wire into 9 the units cover.
8. Stick te ballast on the nearest place from the headlamp in the engine room firmly by using double-faced tape,cable tie and etc.
9. Connect the wire of the ballast with the wire of bulb.
10. Test whether or not the headlamps work properly.