Drawn Cup needle Roller Bearings
Needle bearing with stamped external ring is made of high quality thin sheet by fine stamping process. It has such characteristics as small structure space, large load capacity and etc. and is suitably used for the place where the installing space is limited and case hole cannot be used as the rolling race. After the bearing has been pressed into the seat hole, it is not necessary to make an axial allocation.
For the needle bearing with stamped external ring ,it usually takes the journal as its internal race. Based on the service condition, it can also use a suitable internal ring that can be selected from this catalog.
The structure of needle bearing with stamped external ring is mainly divided into two tyes: the type with fully filled needles and the type with retainer. For each type structure ,it has punched type, closed type, single side sealing ring type and two-side sealing rings, etc. Compared with the retainer type, the fully filled needle type has a great loading capacity but its maximum r.p.m. should not be high. Compared with the punched type ,the closed type has an available seal on the end of shaft.
CQZ can deliver standard needle bearing with stamped external ring of metric and British systems listed in this catalog. CQZ can also deliver non-standard and high accurate bearings with stamped external ring specially required. Please mention it in your order.
CQZ can also develop the needle bearings with stamped external ring suitable for special user according to the special operating condition.
1、Main structural forms
HK Punched type needle bearing with stamped external ring
HK...RS Punched type needle bearing with stamped external ring and with sealing ring on single side
HK...2RS Punched type needle bearing with stamped external ring and with sealing rings on both sides
BK Closed type needle bearing with stamped external ring
BK...RS Closed type needle bearing with stamped external ring and with sealing ring on single side
HMK Punched type heavy-duty needle bearing with stamped external ring
HMK...RS Punched type heavy-duty needle bearing with stamped external ring and with sealing ring on single side
HMK...2RS Punched type heavy-duty needle bearing with stamped external ring and with sealing rings on both sides
F Punched type fully filled needle bearing with stamped external ring
FY Punched type fully filled needle bearing with stamped external ring (grease level limit type)
MF Closed type fully filled needle bearing with stamped external ring
MFY Closed type fully filled needle bearing with stamped external ring (grease level limit type)
2、Inspection on dimensions
Special attention:
Because the thin stamped external ring has a deformation after heat treatment, its dimensions cannot be accurately inspected before installation. The bearing''s dimension can reach its necessary geometric accuracy only after the bearing has been pressed into the standard seat hole .
The deviation of inscribed circle''s diameter(Fw) of needle bearing with stamped external ring shall comply with the stipulation in table 1:
Nominal internal diameter of needle assembling unit Fw(mm) | Fw min=Fw min-Fw | ||
greater than | up to |
upper limit of tolerance |
lower limit of tolerance |
3 | 6 | +28 | +10 |
6 | 10 | +31 | +13 |
10 | 18 | +34 | +16 |
18 | 30 | +41 | +20 |
30 | 50 | +50 | +25 |
50 | +60 | +30 |
The inspection method: press the bearing into the standard seat hole that has a dimension complying with table 2 and has a thickness greater than 20;then use the limit plug gauge listed in table in table 3 to make a measurement.
Nominal internal diameter of needle assembling unit Fw (mm) | Nominal internal diameter of standard ring | Tolerance of standard ring um | Wall thickness of standard ring | |
greater than | up to | |||
6 | 10 | D-0.016 | Tolerance is in accordance with the stipulation of IT8 specified in GB1957 | greater than of equal to 20 |
10 | 18 | D-0.020 | ||
18 | 30 | D-0.024 | ||
30 | 50 | D-0.028 | ||
50 | 80 | D-0.033 |
Nominal internal diameter of bearing Fw (mm) |
Nominal external diameter of plug gauge | Tolerance of plug gauge um | ||
greater than | up to | go gauge | no-go gauge | |
3 | 6 | Fw+0.010 | Fw+0.030 | Tolerance is in accordance with the stipulation of IT7 specified in GB1957 |
6 | 10 | Fw+0.013 | Fw+0.033 | |
10 | 18 | Fw+0.016 | Fw+0.036 | |
18 | 30 | Fw+0.020 | Fw+0.043 | |
30 | 50 | Fw+0.025 | Fw+0.052 | |
50 | Fw+0.030 | Fw+0.062 |
3、Installation
The needle bearing with stamped external ring can get its final dimensions and geometric accuracy only after it has been pressed into the seat hole .The tolerance of seat hole and shaft is recommendded in table 4. When it uses the journal as the rolling race , its surface hardness cannot be lower than 58HRC; its surface roughness Ra shall be less than 0.2um; its roundness and cylindricity shall not greater than 50% of the journal''s dimensional tolerance.
material of bearing seat | dimension tolerance of bearing seat hole | dimension tolerance of shaft |
steel or cast iron | N6 | hs |
light alloy type is used for wall thickness less than 6mm | R6 | hs |
Related Product Tags:
air bearing , auto air conditioner bearing , air conditioner bearing , air conditioner bearings , alternator bearing , alternator bearing ford , alternator bearings , axle bearing , rear axle bearing , ball bearing ring , ball bearing units , ball bearings , automobile ball bearings , ceramic ball bearing , Screw Ball Bearing , contact ball bearing , loose ball bearing , loose ball bearings