Quick Details

• Place of Origin:

  Wuhan, Hubei

• Samples:

  Not Available

• Delivery Time:

  15 Working Days

• Packing:

  Plywood Case

• Max. Production Capacity:

  100 Per Year

• Export Ratio:

  31% - 40%

• OE Experience:

  No

Product Name:SXCF Impulse Voltage Generating Test System

SXCF Impulse Voltage Generating Test System

Application

Acura

Product Description:

This impulse test system is used for carrying out standard lightning impulse voltage full wave and operation wave tests on HV apparatus such as power capacitors, clearance, bushings, power transformers and CT/PT.

Main Parameters for System:

Nominal voltage: 200kV/300kV/400kV/800kV or at customized

Rated stage voltage: 100kV

Rated stage energy: 2.5kJ

Stage Impulse capacitance: 0.5µF

Number of Stages: 2/3/4/8 stages at customized

  Impulse  voltage  waveform:  generated when load capacitance is 300-3000pF.

    T1=1.2µs±30%,       T2=50µs±20%,       standard lightning impulse voltage full waveform of peak voltage deviation3%;

Standard  operation  waveform  250 ± 20%/2500 ± 60%.  These 2 impulse  voltage  waveform      parameters      and     error     are    accorded      with    national      requirements      of GB311.1and GB16927.1 standard and IEC standard.

Voltage utilization factor: Standard lightning impulse voltage waveform 90% when load capacitance is below 1000pF, standard operation impulse voltage waveform80% when load capacitance is below 2000pF. Standard operation impulse voltage waveform 70%.

Locking range: level voltage is within the range of 20%-100%rated voltage, positive and negative locking range no less than 25%.

Out-of-control rate of synchronous discharge: <5%

Min.output voltage: ±20% of rated voltage.

Instability of discharge voltage: <±1.0%

Continuous time: Above 2/3 of rated voltage, continuous working when charge and discharge once every 120s. Below 2/3 of rated voltage, continuous working when charge and discharge once every 60s.

System Configuration:

1. Charging Device

Constant current charging device, rated output voltage±100kV, rated output DC current 10-100mA.

Oil type charging transformer, primary voltage is 220V, secondary voltage is 50kV, rated capacity is 5kVA. No oil leakage of transformer.

2DL-200kV/100mA HV rectifying silicon stack(HV diode), reverse voltage200kV, average current 0.1A. HV diode is installed on the charging board.

Protective resistor of HV diode is made of enameled resistance wire.

Instability of charging voltage <±1% at 15%-100%rated charging voltage of constant charging device. The adjustable accuracy of charging voltage is 1%.

DC resistance voltage divider 100kV, 200m, with HV vitreous glaze resistor. LV resistor is installed at the bottom of divider, while the voltage signal of LV side is lead to measurement system by shield cable.

Automatic earth switch is open and close by electromagnet. Automatically short-circuit main capacitor and ground by protective resistor when testing stops.

Charging transformer, HV silicon rectifier, resistance divider, charging current-limiting resistor and main controller are installed in the same movable chassis.

Change the polarity automatically.

The device is not only used as charging power supply of impulse voltage generat or, but also as DC voltage generator to generate 100kV DC voltage, which can b e used in DC test for other apparatus.

Sansion Power Electric was established in 2005, a technocrat who have rich experience of more than 10 years in R&D, manufacturing and marketing of power electrical testing products, which are widely used in the fields of power electric, railroad, energy conservation and environment protection, ...[Read More]

Company Profile:

• Main Product:

  Ac Dc Hipot Test Set, Ac Resonant Testing Equipment

• Business Type:

  Manufacturer

• Current Export Market:

  North America, South America, Eastern Europe, Eastern Asia, Southeast Asia, Mid East, Africa, Oceania

Factory Profile:

• Size of Factory In Square Meters:

  2000

• Years of OEM Experiences:

  10

Research & Development:

• Capability for Synchronized Development:

  Develop according to drawing or samples provided by clients?Yes

  Develop 3-D model and prototype according to client's needs?Yes

• Tooling Design:

  Design Internally

• Source of Tooling:

  Made Internally

• Software/Profile:

  Others